This took us about 9 hours in total.  Most of the time was spent in cutting and grinding the caps as well as fishing the nuts and bolts into the tight areas.

This video will show parts of the installation of the 4.5-6 Inch Coilover Conversion Upgrade Kit for my 2022 Ram 2500. The instructions from Rough Country for this kit are "OK" at best.  Several differences, but we got it done.

** I am NOT Sponsored by Rough Country, I pay for these products on my own **
I get nothing for you clicking on the link below, just sharing the information for the kit I purchased to make this video.


LINK TO KIT :
https://www.roughcountry.com/product/ram...-kit-31014

Sorry guys... This video is not the best recording since I did it with my iPhone. My Go-Pro died...

In this video I am showing the installation for the Rough Country Air Spring Kit and how I am getting rid of that squat that happens when I connect a trailer to my lifted 2022 Ram 2500.

** I am NOT Sponsored by Rough Country, I pay for these products on my own **
I get nothing for you clicking on the link below, just sharing the information for the kit I purchased to make this video.


Link:
https://www.roughcountry.com/product/con...kit-10029c

UP NEXT ---
Coming soon is the video showing the installation of the 2022 Ram 2500 Coilover Conversion Upgrade Kit.

This video is about how to capture the factory file to send to Optimal using the MPVi3 and HP Tuners Software on your 2022 Ram 2500. This is basically the first step in the process after purchasing the tunes from Optimal.

Steps:
- Install your SGM Bypass cable.
- Connect up your MPVI3 hardware to the OBD2 port and select READ VEHICLE
- Save the .hpt file it gives you.
- Send Optimal your .hpt file, your new ECM serial number (S/N on the sticker) and your MPVI Serial from the back of the device.

This video is about swapping the 2022 Ram 2500 ECM with part# 4384696 from a 2022 Ram 2500. I have seen other part numbers used for this process, but I did not want to run into the same issues. I held out until I could find this part number specifically.

Steps: (Once you have received your tune file from Optimal)
- Open the new custom tune file using the HP Tuner Software and select WRITE VEHICLE.
- Once the write has finished. You're all done and ready to install your aftermarket equipment and SOTF switch.

5 Position Switch video from my 2019 - Same process:
https://youtu.be/abKX9H3sGCo

This video is about how to capture the logs and import the Channels File. I will also cover how to flash the ECU with the new tune file received after Optimal has reviewed the logs sent to them.

Optimal Welding Tunes:
2022-2024 RAM 6.7L CUMMINS - HPTUNERS CUSTOM TUNING
https://optimalindustries.com/products/2...m-tuning-1

Flo-Pro Exhaust: (I used from previous Truck)
FLOPRO SS892 19-20 DODGE RAM CUMMINS 6.7 4" RACE PIPES DPF DELETE STAINLESS

This video is How To install the Rough Country Dual Steering Stabilizer on my 2019 Ram 2500 6.7 Cummins

This was very easy and simple, It took less than 30 minutes total! These are very cost effective and a well made stabilizer kit.

https://www.roughcountry.com/steering-st...49430.html

Made this video to show some of the upgrades done so far to the outside of the 2019 Ram. I just moved into the new house and shooting this video with my new GoPro. Still getting used to it so I apologize for the wind noise..

In this video I will Install the Optimal Welding Tunes using the EFI Live v3 on my 2019 Ram 2500 and installing the 5 Position Switch. I will cover the disconnections and replacement Flo-Pro exhaust in another video.

Optimal Welding Tunes:
Efi Live Custom Tuning for 2019-2020 6.7 Cummins
https://optimalwelding.com/collections/e...-7-cummins

Flo-Pro Exhaust:
FLOPRO SS892 19-20 DODGE RAM CUMMINS 6.7 4" RACE PIPES DPF DELETE STAINLESS
https://www.ebay.com/itm/FLOPRO-SS892-19...2749.l2649